

OTS…(A) Floating skimmer
For removing oils floating on water and sludge that flows easily (see video)
- Inlet on one side
- Apart from the inlet strainer, this device consists of only one part
- This eliminates the need for spare parts
- Connecting piece horizontal or vertical downwards
- available according to ATEX, here with additional earthing connection
- any settings for satisfactory operation are completely eliminated
- Depending on the suction flow rate set on the pump, this device raises and lowers automatically.
- Unsinkable, even with severe damage
- This device is comfortable in strong waves, but oil removal suffers. The water surface should be calm for smooth oil removal.
- with 2 large carrying handles and 2 safety eyelets
- The lid can be unscrewed on request
- Compared to the standard suction nozzle, this is also available one size larger in each case
Size
Overall length
Connection R
1 (A)
250
1“
2 (A)
500
1 ¼
3 (A)
750
1 ½“
4 (A)
1000
2“
5 (A)
1250
2 ½“
6 (A)
1500
3“
7 (A)
2000
4“

OTS…(B) Floating skimmer
For removing oils floating on water (see video)
- 360° inlet
- Lightweight yet robust design, more comfortable handling
- With 3 floats at the top, height-adjustable
- If necessary, 3 additional floats at the bottom
- Lower floats are adjusted together with the upper floats
- The 3 outer floats can be replaced individually, advantage in case of damage!
- With central float integrated on stabilizing ring
- If required, the central float can also be used as a flooding chamber with the aid of the flooding valve if the buoyancy is too strong. The central float is flooded via an arm that carries an outer float. The air inside is then compressed. If the buoyancy is still too strong, the air can be vented via the vent valve, which allows more water to enter.—- This makes the device even more stable on moving water, as the water in the flooding chamber is always horizontal.
- For ATEX with additional earthing connection (also Zone 0, 1 or 2)
- Inlet with handle, height-adjustable, integrated in the middle float, with anti-twist protection
- Inlet itself is one nominal width larger than the oil outlet (suction nozzle), thus rapid flow in
- Under the central float with stabilizing ring and stabilized edge
- Larger devices have two stabilizing rings that are offset
Oil-water outlet nozzles welded under the appliance, horizontally or vertically downwards (depending on requirements), are available to choose from:
- External thread (if the customer provides a hose himself and requires this external thread)
- Hose nozzle (direct hose connection)
- Geka coupling (if we supply a hose or customer request)
- Made entirely of stainless steel in V2A quality or also entirely in V4A quality
- The threaded rods on the underside of the floats are used for anchoring with rope
- For larger devices, the 3 arms can be used for the ropes
- Possible with pump mounted directly underneath, as type OTS-P….(C)
- With stabilizer; in the event of strong water movement, the appliance cannot tip over at all, it stays put.

Size Hose nozzle Connection R
1 (B) 15 ½“
2 (B) 20 ¾“
3 (B) 25 1“
4 (B) 32 1 ¼“
5 (B) 40 1 ½“
6 (B) 50 2“
7 (B) 65 2 ½“
8 (B) 80 3“
9 (B) 100 (A-Ø) 4“
OTS-P….(C) Floating skimmer
For removing oils floating on water.
- 360° inlet
- Including directly under-mounted pump made of stainless steel or plastic (depending on what is possible)
- Lightweight yet robust design, more comfortable handling
- With 6 floats, height-adjustable
- Lower floats are adjusted together with the upper floats
- All outer floats can be replaced individually, advantage in case of damage!
- With central float integrated on stabilizing ring
- If required, the central float can also be used as a flooding chamber with the aid of the flooding valve if the buoyancy is too strong. The central float is flooded via an arm that carries an outer float. The air inside is then compressed. If the buoyancy is still too strong, the air can be vented via the vent valve, which allows more water to enter.—- This makes the device even more stable on moving water, as the water in the flooding chamber is always horizontal.
- For ATEX with additional earthing connection (also Zone 0, 1 or 2)
- Inlet with handle, height-adjustable, integrated in the middle float, with anti-twist protection
- Inlet itself is one nominal width larger than the oil outlet (suction nozzle), thus rapid flow in
- Under the central float with stabilizing ring and stabilized edge
- Larger devices have two stabilizing rings that are offset
- The outlet connection is determined by the pump, which is on the pump
- Made entirely of stainless steel in V2A quality or also entirely in V4A quality
- The threaded rods on the underside of the floats are used for anchoring with rope
- For larger devices, the 3 arms can be used for the ropes

Size
Connection R
1 (C)
½“
2 (C)
¾“
3 (C)
1“
4 (C)
1 ¼“
5 (C)
1 ½“
6 (C)
2“
7 (C)
2 ½“
8 (C)
3“
9 (C)
4“
(The specification of the connection is only a guideline for the size of the OTS…(B) device used, the decisive factor is which pump can be used and is available on the market)
OTS ….(D) Floating skimmer
For removing oils floating on water.
- Made of stainless steel
- Inlet 2-sided, larger appliances 4-sided
- Particularly lightweight design with extremely large extraction area
- With 2 or 4 integrated floats, not height-adjustable
- For ATEX with additional earthing connection (also Zone 0, 1 or 2)
- Inlet with handle, height adjustable
- Inlet same size as outlet
- Made entirely of stainless steel in V2A quality or also entirely in V4A quality
- Welded-on eyelets are possible for anchoring with rope (on request)
- Oil outlet vertical or horizontal with additional 90° bend

Size
Connection R
1 (D)
½“
2 (D)
¾“
3 (D)
1“
4 (D)
1 ¼“
5 (D)
1 ½“
6 (D)
2“
7 (D)
2 ½“
8 (D)
3“
9 (D)
4“
(The volume flow is determined by the pump to be used, which is possible in unpressurized suction operation)
OTS ….(E) Floating skimmer
For removing oils floating on water.
- Made of stainless steel in catamaran design
- Inlet on one side
- Lightweight design with extremely large extraction area
- With 2 floats, horizontally adjustable
- For ATEX with additional earthing connection (also Zone 0, 1 or 2)
- Inlet with handle, height adjustable
- Made entirely of stainless steel in V2A quality or also entirely in V4A quality
- For anchoring using a rope, this can be attached to the device
- Oil outlet vertical or horizontal with additional 90° bend

Size
Connection R
1 (E)
½“
2 (E)
¾“
3 (E)
1“
4 (E)
1 ¼“
5 (E)
1 ½“
6 (E)
2“
7 (E)
2 ½“
8 (E)
3“
9 (E)
4“
(The volume flow is determined by the pump to be used, which is possible in unpressurized suction operation)
OTS ….(F) Floating skimmer
For removing oils floating on water.
- Made of stainless steel, handwheel made of aluminum, self-locking nut made of bronze
- 360° inlet
- Lightweight construction
- With 3 floats, not height-adjustable, individually interchangeable
- With suspended inlet, which is height-adjustable over a wide range using a handwheel, whereby the floats always remain on the water (only the inlet is adjusted)
- This also enables suction below the water surface
- For ATEX with additional earthing connection (also Zone 0, 1 or 2)
- Made entirely of stainless steel in V2A quality or also entirely in V4A quality
- For anchoring using a rope, this can be attached to the device
- Oil outlet vertical or horizontal with additional 90° bend
Size
Connection R
1 (F)
½“
2 (F)
¾“
3 (F)
1“
4 (F)
1 ¼“
5 (F)
1 ½“
6 (F)
2“
7 (F)
2 ½“
8 (F)
3“
9 (F)
4“
(The volume flow is determined by the pump to be used, which is possible in unpressurized suction operation)
OTS-P ….(G) Floating skimmer
For removing oils floating on water.
- Made of stainless steel, handwheel made of aluminum, self-locking nut made of bronze
- 360° inlet
- Lightweight construction
- With 3 floats, not height-adjustable, individually interchangeable
- With directly mounted pump made of stainless steel or plastic, otherwise design as OTS…(F)
- With suspended inlet, which is height-adjustable over a wide range using a handwheel, whereby the floats always remain on the water (only the inlet is adjusted)
- This also enables suction below the water surface
- For ATEX with additional earthing connection (also Zone 0, 1 or 2)
- Made entirely of stainless steel in V2A quality or also entirely in V4A quality
- For anchoring using a rope, this can be attached to the device
- Oil outlet vertical or horizontal with additional 90° bend
Size
Connection R
1 (G)
½“
2 (G)
¾“
3 (G)
1“
4 (G)
1 ¼“
5 (G)
1 ½“
6 (G)
2“
7 (G)
2 ½“
8 (G)
3“
9 (G)
4“
(The volume flow is determined by the pump to be used, which is possible in unpressurized suction operation)
OTS ….(H) Floating skimmer
For removing oils floating on water.
- Made of stainless steel in catamaran design
- Inlet on one side
- Lightweight design with extremely large extraction area
- With 2 floats, horizontally adjustable
- For ATEX with additional earthing connection (also Zone 0, 1 or 2)
- Inlet with handle, height adjustable
- Made entirely of stainless steel in V2A quality or also entirely in V4A quality
- For anchoring using a rope, this can be attached to the device
- Oil outlet vertical or horizontal with additional 90° bend

Size
Connection R
1 (H)
½“
2 (H)
¾“
3 (H)
1“
4 (H)
1 ¼“
5 (H)
1 ½“
6 (H)
2“
7 (H)
2 ½“
8 (H)
3“
9 (H)
4“
(The volume flow is determined by the pump to be used, which is possible in unpressurized suction operation)
OTS-P ….(I) Floating skimmer
For removing oils floating on water.
- Made of PP or PE plastic
- 360° inlet
- Lightweight construction
- With 3 floats, height-adjustable, individually interchangeable
- With plastic pump mounted directly underneath, otherwise same design as OTS…(H)
- Height-adjustable inlet, one nominal width larger than the outlet
- Oil outlet vertical or horizontal with additional 90° bend
- With support feet or safety frame to protect the pump at an extra charge
- Outlet largely adapted
- With handle, larger appliances with transport lugs

Size
Connection R
1 (I)
½“
2 (I)
¾“
3 (I)
1“
4 (I)
1 ¼“
5 (I)
1 ½“
6 (I)
2“
7 (I)
2 ½“
8 (I)
3“
9 (I)
4“
(The volume flow is determined by the pump to be used, which is possible in unpressurized suction operation)
OTS ….(J) Floating skimmer
For removing oils floating on water.
- Made of PP or PE plastic
- Inlet 2-sided, larger appliances 4-sided
- Particularly lightweight design with extremely large extraction area
- With 2 or 4 integrated floats, not height-adjustable
- Inlet with handle, height adjustable
- Inlet same size as outlet
- Welded-on eyelets are possible for anchoring with rope (on request)
- Oil outlet vertical or horizontal with additional 90° bend

Size
Connection R
1 (J)
½“
2 (J)
¾“
3 (J)
1“
4 (J)
1 ¼“
5 (J)
1 ½“
6 (J)
2“
7 (J)
2 ½“
8 (J)
3“
9 (J)
4“
(The volume flow is determined by the pump to be used, which is possible in unpressurized suction operation)
OTS ….(K) Floating skimmer
For removing oils floating on water.
- Made of PP or PE plastic
- Semi-circular design, self-floating
- Inlet 180°
- Particularly lightweight design with extremely large extraction area
- Without float, not required
- Rear inlet, not adjustable
- Oil outlet vertical or horizontal with additional 90° bend

Size
Connection R
1 (K)
½“
2 (K)
¾“
3 (K)
1“
4 (K)
1 ¼“
5 (K)
1 ½“
6 (K)
2“
7 (K)
2 ½“
8 (K)
3“
9 (K)
4“
(The volume flow is determined by the pump to be used, which is possible in unpressurized suction operation)
OTS ….(L) Floating skimmer
For removing oils floating on water.
- Made of stainless steel
- 360° inlet
- Height-adjustable inlet, with handle
- With 3 floats, slightly height-adjustable, individually replaceable
- Horizontal oil outlet
- Under-mounted pump not possible

Size
Connection R
1 (L)
½“
2 (L)
¾“
3 (L)
1“
4 (L)
1 ¼“
5 (L)
1 ½“
6 (L)
2“
7 (L)
2 ½“
8 (L)
3“
9 (L)
4“
(The volume flow is determined by the pump to be used, which is possible in unpressurized suction operation)
OTS ….(M) Floating skimmer
For removing oils floating on water.
- Hanging on a movable or fixed rod
- Oil skimmer floats up and down on the rod
- 360° inlet
- Lightweight construction
- Use on a ship’s bilge tank or in narrow sewers
- Oil outlet vertical or horizontal with additional 90° bend
- No spare parts, no wear and tear

Size
Connection R
1 (G)
½“
2 (G)
¾“
3 (G)
1“
4 (G)
1 ¼“
5 (G)
1 ½“
(The volume flow is determined by the pump to be used, which is possible in unpressurized suction operation)
OTS…(1) Floating skimmer
Oil skimmers and floating oil skimmers for removing oil floating on water or waste water.
- For undemanding and simple applications
- For calm and very slightly moving water surfaces in lightweight construction
- In 2 sizes, each with 3 separate plastic floats, stainless steel rods
- With removable filter insert
- Bottom oil outlet 1″, 1 1/4″, 1 1/2″
- Oil-water removal rate non-binding up to 18 m³/h

OTS-P…(5) Floating skimmer
Oil skimmer Oil floating skimmer for removing oil floating on water or waste water.
- For somewhat more demanding applications
- In sturdy industrial design
- With built-in pump 230 V, 50 Hz
- For calm and up to slightly more moving water surfaces
- One size each with 3 separate floats, 3 pump sizes
- Inlet funnel and float not adjustable in height, made of plastic, up to 35 °C
- With removable filter insert against coarse soiling
- Dirt particles 5-10 mm Ø, non-abrasive
- Bottom oil outlet 1 1/4″ Oil/water removal rate non-binding up to 5.5, 10 or 13 m3/h
- Floating pump

OTS-P…(6) Floating skimmer
Oil skimmers and floating oil skimmers for removing oil floating on water or waste water.
- For very demanding applications
- In a stable and very robust industrial design
- Float made of GRP plastic or stainless steel 1.4301, 1.4308 or 1.4571
- Also according to ATEX
- For oil and floating sludge extraction
- With built-in pump
- For calm and to more moving water surfaces
- With vortex impeller sludge pump with three-phase motor
- Inlet hopper not adjustable in height
- Bottom oil outlet 2″, for ATEX 2″ or 3″
- Oil-water removal rate non-binding up to 85 m3/h
- Floating pump
